Home / Chevrolet / National / National buyer's guide

Chevrolet National buyer's guide

Chevrolet National (1928–1928) — National, AB: what's listed, and what they sell for.

Years: 1928–1928 · Models: National, AB

# Chevrolet AB National (1928) — Buyer's Guide

Overview and history

You are looking at the last four-cylinder Chevrolet for a third of a century. The Series AB National is a one-year car, built for the 1928 model year only, as the successor to the 1927 Series AA Capitol and the immediate predecessor of the 1929 Series AC International. That single fact shapes everything about buying one: there is no model-year spread to shop across, no mid-run engine change to chase, and no facelift to prefer. Every genuine National is a 1928, every genuine National left the factory with the same 171 cu in overhead-valve four and the same three-speed manual gearbox, and every difference that matters between two cars in front of you is body style, condition, originality, and the quality — or the violence — of what ninety-odd years of owners have done to it since.

The context is the fiercest sales fight of the early industry. Ford had finally killed the Model T and launched the all-new Model A for 1928, priced aggressively. Chevrolet's answer was not yet the famous overhead-valve six — the so-called Cast Iron Wonder did not arrive until 1929 — but a thoroughly worked-over version of the car it already had. The wheelbase grew four inches, from 103 to 107 inches, and the extra length went in ahead of the firewall, lengthening the bonnet. That was not vanity: the longer bay was already sized for the six Chevrolet knew was coming, which is why it takes a second look to tell an AB from the six-cylinder AC that followed it. Treat that resemblance as a buying hazard, not a curiosity.

The styling itself is historically significant out of proportion to the car's price when new. The AB's tidier, lower, more integrated look — fuller crowned wings, a higher cowl line, larger headlamps on a crossbar — was one of the first projects of General Motors' new Art and Colour Section under Harley Earl. You are not buying a styled-afterthought economy car; you are buying one of the first mass-market cars whose appearance was deliberately designed rather than merely engineered.

Mechanically, the headline advance for 1928 is braking. The National is the first Chevrolet with brakes on all four wheels — mechanically actuated drums, rod-and-cable operated, not hydraulic — where the Capitol had braked the rear wheels only. The second headline is the engine's final development: higher compression, larger valves, aluminium pistons and a revised carburettor, lifting the old 171 cu in four to 35 hp at 2,200 rpm. Do not let anyone sell you that as a performance gain: the AB is also a bigger, heavier car than its predecessors, at roughly 2,030 to 2,435 lb depending on body, and the extra power essentially keeps pace with the extra weight. What you get is a car that cruises honestly at the speeds its brakes, tyres and steering were designed for — a 40–45 mph working gait — and asks to be driven sympathetically.

Commercially the car was an unqualified success. Documented production is 1,193,212 Series ABs across all body styles and plants, with 69,217 of those from Oshawa in Canada alone, and Chevrolet ended 1928 as the American sales leader. Abundance when new, however, does not mean abundance now: a cheap, hard-used, wood-framed car from 1928 was worth almost nothing through the Depression and the war years, and most were simply consumed. Our own pool at the time of writing is tiny — three cars — and it illustrates the survivor spread exactly: a restored green closed coupe in Illinois, a yellow roadster project in Pennsylvania wearing as much primer as paint, and a purple two-door sedan in Florida converted into a street rod. With a National, you are never really shopping the model. You are shopping the individual car's structure, its wood, and its history.

One myth to kill immediately: the National does NOT have a six-cylinder engine, hydraulic brakes, or an automatic gearbox, and it never did. Any National offered with those things has been modified — sometimes well, often not — and must be valued as a modified car, not as a rare factory variant. There were no factory variants of that kind.

1928 Chevrolet AB National roadster project, front three-quarter view
The project end of the market. This Morgantown, Pennsylvania roadster shows the AB face you must learn: tall narrow radiator shell with the Chevrolet emblem at its crown, two large drum headlamps on a crossbar, full crowned front wings and steel disc wheels. Note how much of the yellow finish is already grey primer — on a roadster, paint failure is the least of your costs. What you are really pricing here is the wood framing under that skin, the top, the interior and a full mechanical recommissioning.

The models

Because the National ran for one year with one engine and one gearbox, the model range is a body-style range and nothing else. Fisher Body supplied the coachwork for the American cars, and the catalogue offered eight styles spanning open and closed bodies, from the basic roadster to the Imperial Landau at the top. In practice, the cars you will actually be offered are a narrower set: the two-door Coach and four-door Sedan account for most closed survivors, the Coupe survives in useful numbers, and the open Roadster and Touring survive in smaller numbers and far more variable condition, because an open, wood-framed body exposed to weather for ninety years deteriorates in ways a closed body sheltered by its roof does not. The Landau styles survive least well of all: when the fabric covering fails, water goes straight into the wood and the rear body rots from inside a car that can still look presentable in a photograph.

Read the table with that survival logic in mind. Output is the same 35 hp for every car, because the engine is the same. Where a per-body production figure is not reliably published, the table says so rather than inventing one.

ModelYearsEngineOutputBuiltCharacter
Roadster1928171 cu in OHV four35 hp @ 2,200 rpm— (see total below)The cheapest way in when new and the most expensive way in now if it needs wood, top and trim; folding windscreen, minimal weather protection
Touring1928171 cu in OHV four35 hp @ 2,200 rpm—Four-door open tourer; the family open car, and the most wood- and canvas-dependent body of all — buy only on structure
Coupe1928171 cu in OHV four35 hp @ 2,200 rpm—Two-seat closed coupe, some with a dickey (rumble) seat and some with fabric-covered roof treatment; the best-balanced survivor — closed-car shelter, simple trim
Coach1928171 cu in OHV four35 hp @ 2,200 rpm—The two-door sedan; the volume closed car and the one you will see most often — judge it on wood and doors, not on rarity
Sedan1928171 cu in OHV four35 hp @ 2,200 rpm—Four-door, five-passenger closed sedan; the heaviest body at the top of the weight range and the most interior to retrim
Landau Sedan1928171 cu in OHV four35 hp @ 2,200 rpm—Sedan with fabric rear quarters and landau irons; the trim is the point and the rot risk — inspect the rear quarters as structure, not decoration
Imperial Landau1928171 cu in OHV four35 hp @ 2,200 rpm—The flagship of the range and the most expensive National when new; blind rear quarters, the most formal body, and the hardest to restore honestly
Series total1928171 cu in OHV four35 hp @ 2,200 rpm1,193,212 documented (incl. 69,217 Oshawa)One year, one engine, one gearbox — every buying decision is body, condition and originality

Two distinctions inside that table deserve more than a row. The first is open versus closed, because it is really a distinction about water. A closed Fisher body sheds most weather off its roof and panels, and its wood framing — and there is a great deal of it — stays dry for decades if the roof insert and window seals hold. An open car's framing and floor live one failed top or torn side curtain away from saturation, and the rot that follows is structural, not cosmetic. That is why two Nationals with identical paint and engines can be a full restoration apart in value. The second distinction is the Landau treatment: the fabric-covered quarter and decorative landau iron look wonderful and are a standing water trap. If you want a Landau, you want one whose quarters have been restored with the wood underneath proven, with photographic evidence, not an assurance.

Wheels are worth noticing rather than memorising. Steel disc wheels were common fitment and are what both honestly original cars in our pool wear; wood-spoke artillery wheels were also period fitment, and either can be correct — what is never correct is a modern alloy wheel, a wide radial tyre, or a lowered stance, all of which tell you the car has passed through street-rod hands. What changes value is whether the body style on the car is the body style the chassis left the factory with, and on a car whose serial number lives on a plate at the front seat heel board rather than in a modern VIN system, that question is answered by the Fisher body plate and the car's paperwork. There is no modern VIN to decode. Anyone who offers you a decoded printout for a 1928 Chevrolet is selling you theatre.

Finally, Chevrolet also built light-delivery variants on a beefed-up version of the same chassis — panel and canopy-express bodies, half-ton pickups and chassis for ambulance and hearse work. They are legitimate vehicles, but not passenger Nationals, and should be bought and valued as commercials.

1928 Chevrolet AB National roadster, side profile
Read a National in profile and the 1928 changes explain themselves: the long louvred bonnet, the four extra inches of wheelbase ahead of the cowl, the running board between full wings, and the upright folding windscreen are all AB identifiers. On this project roadster, look past the patchy finish to the shut lines: the door still hangs square in its aperture, your first, cheapest evidence that the wood framing underneath has not yet sagged. When the door drops, the wood — not the hinge — is usually the reason.

Engines and gearboxes

There is exactly one engine to learn, and you should learn it thoroughly, because on a car this old the engine is where a seller's story and the metal in front of you most often part company. Every National carries Chevrolet's 171 cu in (2.8-litre) overhead-valve inline four. There is no optional engine, no high-output variant, and no six-cylinder National. If the car in front of you has six cylinders, a V8, fuel injection, an alternator or an automatic gearbox, you are looking at a different kind of car altogether, and you should decide whether you want a modified car before you discuss its price at all.

The 171 four: architecture and bottom end

The design is old even by 1928 standards, which is a compliment to its durability and a warning about its limits. The block is cast iron, the head is detachable, and the valves sit in the head, operated by pushrods and rockers from a camshaft in the block — a genuine overhead-valve layout at a time when Ford's Model A still used a flathead, side-valve engine. The arrangement gives the four a breathing efficiency its side-valve rival cannot match. The firing order is 1-2-4-3. Treat that as an inspection tool: a car that runs lumpily with its plug leads in the wrong order is telling you about its last mechanic, not about its engine.

The bottom end is where the era shows. Bearing practice and lubrication belong to the world of poured babbitt bearing metal, careful hand fitting, and splash-and-feed lubrication rather than the full-pressure, shell-bearing world you may know from later engines. The consequences are threefold. First, bearing condition cannot be judged from a cold, quiet start; babbitt wear announces itself as low oil pressure when fully hot and a deep, load-dependent knock, so the only honest test is a proper run to full temperature, listening under load and watching oil pressure hot at idle. Second, a rebuild is a specialist job: repouring and line-boring babbitt in period fashion is work for a machine shop that does pre-war engines routinely — budget $6,000–12,000 if the bottom end is genuinely tired, and treat a cheap recent "rebuild" with no paperwork as no rebuild at all. Third, lubrication discipline is the engine's life: clean oil, changed far more often than a modern car asks. Ask the seller what oil is in it and when it last changed. A blank look is data.

Do not be talked into the myth that the four is fragile because it is old. A correctly rebuilt example, driven at period speeds and fed clean oil, is a reliable engine. What kills them now is not design but deferred maintenance, overheating and frost damage.

The 1928 development: head, valves, pistons and breathing

For its final year the engine received the most complete set of updates it ever had. Compression was raised, the valves were enlarged, aluminium pistons replaced the earlier practice, and the carburation was revised, together lifting output to 35 hp at 2,200 rpm. Two things follow for a buyer. First, internal parts are year-sensitive in detail even though the engine looks identical to a 1927 Capitol four at a glance: a car rebuilt with whatever was on the shelf may run acceptably while being quietly wrong — wrong enough to matter when you sell it on. Ask what was fitted at rebuild and expect receipts to name parts, not just labour. Second, the valvetrain needs you. Valve clearances are set mechanically and drift with wear and valve-seat recession — a live issue on any engine designed for leaded fuel and now run on unleaded. A completely silent top end is not a sign of health; correctly set clearances make a light, even mechanical sound, and silence can mean clearances closed to nothing, which holds valves off their seats, burns them, and presents later as low compression that gets blamed on rings. The distinguishing test is a compression test read alongside a clearance check: low compression on one cylinder with a closed-up clearance is a valve problem until proven otherwise; low compression evenly across all four with correct clearances points at general wear.

Oil weeps at the top of the engine are normal in kind, if not in degree. A film around the rocker cover on a driven car is period behaviour; oil running down the block or dripping steadily at hot idle is a seal or gasket problem to price. And learn the cold-start ritual before you judge starting at all: choke and hand throttle set by the driver, on a 6-volt system turning an engine that expects your help. A car that needs three attempts on a cold morning with the controls set correctly may still be healthy. A car that will only start on a booster pack, ether, or a tow has a fault, and the seller's patter about "they all do that" is the fault's accomplice.

Fuel, ignition and cooling: the systems that actually stop these cars

Most Nationals that "won't run right" are not suffering engine failure. They are suffering the three support systems, each with a failure mechanism you can test for. Fuel reaches the engine by the period vacuum-tank system: engine vacuum draws petrol from the rear tank into a small vacuum tank under the bonnet, from which it feeds the single-barrel updraft carburettor by gravity. There is no electric pump and, on an original car, no mechanical pump of the later pattern. The vacuum tank's failure mode is starvation that mimics carburettor disease — the car starts, runs, fades under load or after a few miles, recovers after standing, and repeats. The mechanism is loss of vacuum integrity: perished seals in the tank, or an air leak in the vacuum line from the inlet manifold, mean the tank cannot refill as fast as the engine drinks, so the car runs out of fuel with a full tank aboard. Watch behaviour against time and load, and inspect the vacuum tank before anyone sells you a carburettor rebuild. The carburettor itself — a single updraft unit, Carter-built units being the period fitment you will most often meet — suffers varnish and sediment from standing, a float and needle valve that stick or sink, and jets that behave leaner and dirtier on modern ethanol-blended petrol than on the fuel they were jetted for. Budget $400–900 for a specialist overhaul, and regard a car that has stood for years as needing the whole fuel path cleaned as one job.

Ignition is battery-and-coil with a distributor, Delco-Remy equipment in period, on a 6-volt system with a generator — not an alternator. A marginal coil or tired condenser gives you a car that starts cold and misfires hot; worn distributor bushings scatter the timing in a way no carburettor adjustment will cure; and any 6-volt system punishes dirty earths with slow cranking that gets misdiagnosed as a dead starter or battery. The test sequence costs nothing: clean, tight connections first, a known-good battery second, points gap and timing third, and only then component replacement.

Cooling is by water pump and radiator with a thermostat fitted, and its enemies are scale, silt and a radiator core recored badly or not at all. A four that overheats finds every other weakness in the car: it thins the oil, stresses the babbitt, warps what can warp and cracks what cannot. Overheating on a test drive is never a small fault. It is either a radiator job — a correct recore and full system clean, typically $800–1,800 — or the symptom of a cracked or distorted casting, a different order of expense. Walk the temperature up slowly and watch it at a standstill afterwards; a healthy system stabilises, a sick one keeps climbing.

Gearboxes: the three-speed manual, and the automatic that never was

The gearbox is a three-speed, floor-shift manual with sliding-mesh engagement — no synchromesh. First gear is for starting, second does most of the car's working, and top is a cruising gear for a car whose natural gait is well below modern traffic speeds. Gear changes require you to match speeds yourself: pause, and double-declutch on downchanges, exactly as every driver in 1928 did. A gearbox that crunches when a modern driver rushes it is not necessarily worn; the distinguishing tests are whether it changes cleanly in practised hands, whether it jumps out of gear under load or on the overrun — that is wear, in the engagement teeth, selector mechanism or bearings, and it does not heal — and whether it whines in one gear only (a gear local to that ratio) or in all gears including neutral with the clutch engaged (which points at the input side, not the gear cluster). A box run low on oil wears its bushes and then its gears, and a specialist overhaul, if gears must be sourced or made, runs $2,500–5,000 and upward. The clutch is a single dry plate, mechanically operated: it should take up without judder (oil contamination, a distorted plate, or tired linkage), should not slip under full load in top on a gradient, and its free play should be present and correct, because a clutch with no free play is being held half-open and wearing itself out.

And the automatic: there is none, there never was, and the point deserves its own paragraph because our own listing pool contains a National recorded with an automatic gearbox. That car is a street-rod conversion, and conversions of exactly this kind are the single largest identity fault in the National market. A conversion is not automatically a bad car. It is, however, a car whose value, insurability, club eligibility and resale audience are entirely different, and whose engineering quality ranges from professional to dangerous. If you meet one, inspect it as a one-off special: who built it, to what standard, with what documentation? Never pay original-car money for it, and never let a seller describe it as a rare factory option. The factory offered you three speeds, a floor lever, and your own left leg. Anything else arrived later, with a cutting torch.

1928 Chevrolet AB National coupe, front three-quarter view
The restored end of the market, and your reference for what correct looks like. This Saint Charles, Illinois closed coupe wears the tall mesh-filled radiator shell with the bowtie emblem, the headlamp crossbar, black wings over a dark green body, cream steel disc wheels and a fabric roof insert. Compare every car you inspect against this face: a modern grille insert, sealed-beam pods or turn-signal stalks sprouting from the wings are all later hands at work. Note the crank hole at the bottom of the shell — the starting handle was still a working part of this car's life, not a decoration.

Problem areas

A National's problems divide cleanly into the ones that cost money and the ones that cost the car. Paint, chrome and trim cost money. Wood, castings and identity cost the car. Work through this section in that order — structure first, mechanics second, cosmetics last — and you will never make the classic National mistake, which is buying a shiny car whose doors no longer meet their apertures.

Body structure: the wood is the car

Here is the fact that governs every Fisher-bodied Chevrolet of this era, and the one most buyers arriving from later, all-steel cars do not know: the steel panels you see are a skin over a hardwood framing skeleton. The body's strength and shape live in ash framing — sills, pillars, door frames, roof rails and rear body structure — with the steel nailed and screwed over it. Ford's Model A used less wood in most bodies; Chevrolet's Fisher bodies used a great deal, and ninety years later that difference is the whole ballgame. Steel rusts where you can see it. Wood rots where you cannot, and takes the body's geometry with it.

The mechanism is always water plus time. Water enters at the roof insert on closed cars — the fabric-covered centre roof panel perishes and leaks onto the roof rails and down the pillars — at window channels and seals, at the windscreen base, around the rear quarters on Landau bodies whose fabric covering has failed, and from below, where road water sits against the sills and floor. Fungal rot softens the ash from inside; screws lose their grip; joints open; and the symptoms you can detect without dismantling are all geometric. Doors that drop and must be lifted to latch. Door gaps that are wedge-shaped. A windscreen frame that no longer sits square. Body lines that wave when you sight along the car. Learn to separate hinge wear from wood failure with one test: open the door halfway, lift it gently at the rear edge, and feel where the movement is. Play at the hinge pin is a hinge job, measured in tens of dollars. Movement of the whole door frame in its aperture, or latch alignment that changes when you jack one corner of the car, is wood, measured in thousands.

Cost honesty matters here, because woodwork is the job sellers most often minimise. Replacing a single rotted sill or pillar section is coachbuilding labour: $1,500–4,000 per major section is a realistic planning range, and a body needing comprehensive reframing is a $10,000–25,000 undertaking before paint, with the car dismantled for months. A skilled woodworker can copy a surviving original section as a pattern, which is why a rotted car with complete, if soft, wood is a far better prospect than a car whose wood was thrown away and replaced with guesswork or steel tubing. Ask directly: has any body wood been replaced, by whom, and is there photographic evidence? On a restored car, the absence of wood photographs in the file is itself an answer.

Steel rust, by comparison, is the honest, visible disease. The map is predictable: the lower edges of the wings where they meet the running boards, the running boards themselves, the bottoms of the doors and rear panels, the valances, the floor edges, and around the fuel tank. Surface rust on a project car like the yellow roadster in our pool — grey primer over failing paint across most panels — is not the issue. What you are hunting is perforation at panel bottoms, bubbling under older restoration paint at the door and quarter bottoms (filler over rust, the signature of a cosmetic restoration), and rust in the frame itself, particularly at spring hangers and crossmember junctions, where mud lodges. A frame that is thin, cracked at a hanger, or bent reframes the whole purchase: structural welding is $2,000–6,000 before you have touched the body, and a bent frame on a car with wood problems turns a project into a parts car. Check alignment with your eyes first, and with a tape measure between wheel centres if anything looks off.

Two further structural traps deserve naming. The first is the roof insert on closed cars: replacing the insert material is a few hundred dollars and a day's work, but a leaking insert left for a decade delivers the pillar and roof-rail rot described above, so treat damp headlining and water staining as structural evidence, not trim faults. The second is the open car's top: a roadster or touring missing its top irons, bows or curtain frames is missing parts far harder to source than fabric, and a complete new top with irons fabricated can run $3,000–6,000. Inventory the ironwork, in person, before you value any open car.

Engine and driveline wear: what ninety years actually does

Top of the engine triage list is cracking. Cast-iron blocks and heads of this age crack from freezing — water left in the system expanding in a hard winter — and from overheating, and the cracks hide at the water jacket, around valve seats and along the deck. A crack repaired well by pinning or stitching can serve for years; a crack repaired with sealant tipped into the radiator serves until your first long run. The tests are a cooling system that holds pressure, oil and water that stay resolutely separate — emulsion under the oil filler or oil sheen in the radiator water are the two directions of the same failure — and no unexplained coolant loss over a proper drive. A head or block crack moves you into engine-out, specialist-repair money, $3,000 and upward before the rebuild you may also need.

Second is bearing and bore wear, judged hot: oil pressure that collapses at a hot idle, a knock that arrives under load as the oil thins, and blue smoke that separates into its causes by timing — smoke on start-up after standing points at oil draining past valve guides; smoke under sustained load points at rings and bores; smoke on the overrun points back at the guides. A compression test, dry and then with oil added through the plug hole, separates rings from valves: compression that rises with oil is rings and bores; compression that does not is valves and seats. Third is the valvetrain: worn rocker shafts and bushes, tired springs, and seats receded by decades of running, first on leaded and now on unleaded fuel. A top-end overhaul is $1,500–3,500 at a specialist, which is why a car with documented head work is worth real money over an identical car without it.

The driveline behind the engine wears more slowly and complains more honestly. The rear axle — period ratio around 3.82:1 — whines from worn crown wheel and pinion or tired bearings, and leaks from its seals onto the rear brakes, which is where an axle fault becomes a safety fault; oil-contaminated rear linings mean new linings and new seals together, never linings alone. The period torque-tube driveline wants its universal joint inspected for play, because play there presents as a clunk on taking up drive that gets blamed on the gearbox. The gearbox itself is judged by the jump-out test: a box that stays in gear under load and on a trailing throttle, in practised hands, is a sound box whatever it sounds like to a synchromesh generation.

Brakes, steering and chassis: the mechanical safety case

The AB's four-wheel brakes were its period pride, and they are the system a modern buyer most dangerously misunderstands. They are mechanically actuated — pedal effort transmitted by rods and cables to expanding shoes in drums at all four wheels — and a mechanical system is only ever as good as its adjustment and friction surfaces, because there is no hydraulic self-equalisation to hide unevenness. Stretched cables and worn rod linkages give you a long pedal and one wheel doing another's work, so the car pulls under braking — and on a mechanical system, pulling is an adjustment and condition report, not a personality trait. Worn operating-cam bushings are a documented early-Chevrolet disease: the cam at each wheel pivots in a brass bushing that receives no regular lubrication, wears oval over high mileage, and can let the cam over-centre and lock a wheel on, so a brake that drags, heats, or sticks after standing is a bushing suspect before it is a lining suspect. Linings may be ancient, oil-contaminated, glazed, or worn down to their rivets and scoring the drums. Drums skimmed repeatedly run thin, overheat and crack. And left standing, the system corrodes: moisture bonds linings to drums, which is why a stored National should never be stored with the parking brake applied, and why your first brake test is at walking pace, feeling for pull, grab and drag.

A full mechanical brake overhaul — drums measured and skimmed or replaced, new linings, cables and rods renewed or adjusted, cam bushings replaced, the system centralised and adjusted by the book — is $1,500–3,500, and it is the best money you will ever spend on the car. A car converted to hydraulic brakes has been modified, and its value and inspection change accordingly; a car whose seller tells you mechanical brakes "stop fine" while the pedal goes most of the way to the floor has told you the brakes need the overhaul above.

Steering and front axle wear complete the safety case. The steering is a worm-type box driving a drag link to a beam front axle on semi-elliptic leaf springs, with kingpins locating the pivots. Wear accumulates at every joint in that chain and presents as one summed symptom: free play at the wheel rim and a car that wanders and must be herded. Measure it with the front wheels on the ground: more than a couple of inches of free movement at the rim before the road wheels respond is a system asking for its worn links to be renewed, $800–2,500 depending on whether the box itself needs rebuilding. Kingpin wear is tested by jacking the wheel and rocking it top and bottom; bearing play rocks in every direction, kingpin play in one plane — learn the difference on the car, because the bills are different. Leaf springs sag, break leaves, and wear their shackle bushes until the axle can move under braking, which feels like brake snatch and is actually the axle steering itself. Tyres close the subject: tall, narrow tyres — period size in the 29×4.75 class on 21-inch rims — whose age matters more than their tread. A correct new set, with tubes, is $1,200–2,000 you should budget without resentment on any car that has stood.

Electrics, interior and trim: the slow decay

The 6-volt electrical system fails by resistance and by age, not by mystery. Original wiring insulation perishes and is repaired in patches by every generation of owner, so judge the harness as a wear item: brittle, taped and spliced wiring throughout is a rewire waiting to happen, $1,500–3,500 for a correct reproduction harness fitted, and a car already rewired has had one of the big ownership jobs done for you. The generator must actually charge, and the starter must crank a hot engine as willingly as a cold one — a starter that fades hot is telling you about its brushes, bushings or the engine's earth strap. Lighting is dim by modern standards even when perfect, and dangerously dim when reflectors have tarnished. Do not let a seller present a 12-volt conversion as an unqualified improvement without asking what else was changed to suit it; a half-executed conversion is two electrical systems fighting. A full set of dead instruments on a "restored" car tells you the restoration stopped where the photographs stopped.

Interior and trim are where restoration costs go to be underestimated. Closed cars carry cloth upholstery — the corduroy-type bench trim in our Illinois coupe's photograph is the honest period character — and a full retrim, with seat springs rebuilt, door cards, headlining and carpets, is $4,000–9,000 at a trimmer who knows pre-war work. Wood-rimmed steering wheels crack; rubber mats perish; plated fittings pit and cost $150–400 per piece to replate properly. None of this stops a car being bought. All of it belongs in your arithmetic, because the National's purchase price is famously the smallest cheque you will write for it.

1928 Chevrolet AB National coupe interior, bench seat
Inside the Illinois coupe: a single wide bench in ribbed cloth, cloth door cards, and everything within reach of the driver because everything is operated by the driver. Sit in an interior and work backwards from condition to history: even, honest wear like this is a car that has been used and kept; a brand-new interior in a car with tired mechanics is a car prepared to be photographed. Check the seat springs by sitting, not by looking — a collapsed spring unit is felt in thirty seconds and costs like upholstery, because it is.

How to inspect one

Inspect a National in the order this list runs, cold car first, because half of what you need to know is only visible before the engine warms and the oil thins. Take a torch, a small magnet wrapped in cloth, a tape measure, a friend, and more time than the seller expects.

  1. Identity before everything. Find the serial plate at the front seat heel board and read the assembly-plant code against the known plant list — Flint, Tarrytown, St. Louis, Kansas City, Oakland, Lakewood, Norwood, Buffalo and Janesville all built ABs. Find the Fisher body plate and confirm the body style it names is the body style on the car. Confirm the engine is a four: count the cylinders and look for the overhead-valve head. A six, a V8 or an automatic gearbox at this step ends the inspection of an "original" car — you are now inspecting a conversion, on conversion terms.
  2. Paper and title. Establish what title the car actually carries. Pre-war cars change hands on bills of sale more often than modern buyers expect — at least one well-known National roadster has been offered with no title, bill of sale only — and the acceptability of that depends on your state's rules. Resolve it before money, not after.
  3. Cold engine bay. Before starting, look for the crack evidence from the problem-areas section: oil in the radiator water, emulsion at the oil filler, coolant stains streaking the block, sealant tipped into the radiator neck, and frost-damage repairs on the jacket. Check oil and coolant levels — a seller who presents a cold car already low on coolant has answered a question for you.
  4. Cold start, your hands. Set the choke and hand throttle yourself, or watch closely while the seller does. The car should start on its 6-volt starter without boosters or ether. Listen for the bearing knock that fades as oil pressure rises — a few seconds of rattle that never returns is one thing; a deep knock that persists or returns under load is the babbitt talking. Note the exhaust colour from the first puff onward.
  5. The wood test, standing still. Work the doors exactly as the body section describes: lift each door at its rear edge and separate hinge play from frame movement; check every gap for wedge shape; sight along both sides for wave; on a closed car, look for damp, staining and musty smell at the pillar bases and roof edges; on an open car, inventory the top irons and bows physically. Then have your friend watch the door gaps while you jack one front corner: gaps that visibly change are a flexible — which is to say, rotting — body.
  6. Steel and chassis. Magnet and torch along the wing bottoms, running boards, door bottoms, rear quarters and valances; bubbling under paint at panel bottoms means filler over rust until proven otherwise. Underneath, examine the frame at spring hangers and crossmembers for thinning and cracking, and measure wheelbase both sides — both should read 107 inches, and the same as each other.
  7. Wheels and tyres. Confirm the wheels are period steel disc or wood-spoke artillery wheels, not modern alloys; check wood spokes, if fitted, for looseness and rot by grip and by sound — a loose spoke ticks, a rotten one is silent and soft. Read the tyre date codes, not the tread depth.
  8. Hot run and oil pressure. Drive long enough to reach full temperature — twenty minutes of mixed work, not a circuit of the block. Watch oil pressure hot at idle against the cold reading, listen for the load knock on a gentle gradient in top gear, and watch temperature behaviour at a standstill afterwards. A system that stabilises is healthy; one that keeps climbing is the cooling bill arriving early.
  9. Gearbox and clutch, in practised fashion. Change gear slowly, double-declutching downchanges, before you judge any crunch — then test for the real fault: full load and trailing throttle in each gear, feeling for jump-out. Test the clutch for judder on take-up and slip in top on the gradient. A clunk taking up drive points to the universal joint and axle, not automatically to the gearbox.
  10. Brakes, from walking pace upward. First stop from walking pace, straight line, light hands: feel for pull, grab and drag. Then a firm stop from 30 mph. Then walk around touching each drum area for the one that is hot — the brake that works too much, or never releases, which the cam-bushing fault in the problem-areas section explains. A long pedal, a pull, or one hot drum each price the full mechanical overhaul.
  11. Steering and axle. Front wheels on the ground, measure free play at the wheel rim; then jack each front wheel and rock it to separate kingpin play from bearing play by the plane of movement. On the road, the car should track with fingertip corrections, not be herded. Check the rear axle for whine, and inspect the rear backing plates for the oil weep that means axle seals — and contaminated linings — together.
  12. Fuel behaviour over distance. The vacuum-tank fault hides on short drives, so make yours long enough to find it: a car that fades after several miles, recovers after standing, and repeats is starving at the vacuum tank, not suffering carburettor trouble, whatever you are told. Finish by re-checking, hot, for fuel weeps, for charging on the ammeter, and for every instrument doing its job. Then — and only then — talk about paint.

Values

The build below this guide appends the live numbers — what Nationals are listed at now, and what recorded sales have achieved — and you should read those numbers through the lessons in this section, because on a one-year, one-engine car the spread between the cheapest and the dearest National is almost entirely a spread of condition and correctness, not of specification. Ignore that spread and the cheapest car in the list will look like a bargain when it is actually the most expensive car there, wearing its costs in a different order.

The first lesson is that condition categories mean more here than on younger classics. A National divides into a restored and sorted car, an older restoration or honest original that drives, a complete project, and a parts car — and the money distance between categories is dominated by three jobs whose costs this guide has already given you: body wood, a specialist engine rebuild, and a full mechanical brake overhaul, with a retrim close behind. When you compare two asking prices, do not compare the cars' paint. Compare which of those four jobs each car has provably had done, with photographs and receipts, and which it is quietly waiting for. The car that costs more and has had its wood done is the cheaper car.

The second lesson is the asking-versus-achieved gap, which on pre-war cars of this class is structural rather than incidental. The audience is knowledgeable but small, no two cars are truly comparable, and sellers price in the negotiation they expect. Recorded achieved prices in the market block therefore deserve more weight than asking prices, and a car that sits listed for months is the market giving you information: at that figure, the buyers who know these cars have looked and passed. Ask what they saw. Often it is in this guide: wood, a conversion, or a title problem.

The third lesson is where the premiums live. Open bodies — a genuinely sound roadster or touring — carry a premium over closed cars in equal condition, because fewer survive sound; but the premium inverts the moment the open car needs wood and top work, when it becomes the cheapest entry and the dearest outcome in the range. Landau bodies carry a rarity premium only when their quarters and the wood beneath them are proven; unproven, rarity is a liability wearing a compliment. Originality carries its own premium: an unconverted car with its four, manual gearbox, mechanical brakes and 6-volt system intact is worth more than a cosmetically superior modernised car, because the original can be sold to every buyer in this market and the converted car only to some. Documentation is a variant in its own right: the car with a file showing wood, engine and brakes is a different financial object from the identical car with a shiny finish and a story.

The project-versus-driver gap is where National buyers most often deceive themselves. A complete, honest project can be the right buy — but do the arithmetic before you conclude that the gap between project price and driver price is your profit. On this car, that gap is usually smaller than the cost of closing it. Buy the project for the pleasure of the work, or buy the driver for the driving. Do not buy the project as a discount on the driver.

1928 Chevrolet AB National two-door sedan, street-rod conversion
The same name, a different species. This Ocala, Florida car wears a National two-door sedan body in a modern purple finish, but look at what the photograph itself tells you: polished modern alloy wheels, low-profile modern tyres, modern bucket seats visible through the glass, an exposed later engine and a stance no 1928 chassis ever had. This is a street rod, recorded with an automatic gearbox — a fitment the factory never offered. It is not an original National and must not be priced as one.

Parts and ownership

Owning a National is an exercise in belonging to the right world rather than in searching a parts catalogue, and the good news is that the world is well organised. The Vintage Chevrolet Club of America is the centre of gravity for pre-war Chevrolet knowledge — its forums carry decades of repair experience on exactly the systems this guide flags, from babbitt practice to mechanical-brake cam bushings — and specialist suppliers such as The Filling Station have built their businesses on early Chevrolet parts: brake components, gaskets, wiring harnesses, wood and trim items, and the thousand small fittings general suppliers never stocked. Between club knowledge, those specialists, and the sheer production volume of 1928, mechanical parts supply is better than for almost any other car of the year. What is genuinely scarce is body-specific: Landau ironwork, open-car top irons, sound original wood sections to copy, and correct fittings for the less common bodies. Buy a complete car over a dismantled one for exactly that reason.

Running the car asks for a rhythm, not a budget crisis. Oil changes are frequent and cheap; valve clearances want checking on a schedule, for the reasons the engine section gives; the chassis wants its grease points attended to — period Alemite practice assumed lubrication in hundreds of miles, not tens of thousands — and the mechanical brakes want their adjustment verified as a routine, because a mechanical system drifts out of equalisation in normal use. Tyres, tubes, 6-volt batteries and linings are all obtainable without drama. Modern fuel is the standing negotiation: run fresh petrol, expect to clean the vacuum tank and carburettor if the car stands for months, and settle the unleaded question with hardened seats at any head work. None of this requires a specialist on retainer. It requires an owner who drives the car regularly, because standing still is the most destructive thing that happens to a National — brakes seize, fuel varnishes, wood stays damp, and seals dry out, all at once.

Storage and use follow from that. Store dry, with the parking brake off, keep fuel fresh or drained for a long lay-up, and exercise the car through the winter rather than entombing it. Drive it at its gait: it tours happily at 40–45 mph and is at its best on club runs and secondary roads. Insure it with an agreed value that reflects the restoration arithmetic in this guide rather than the purchase price, and keep the file — receipts, wood photographs, engine work — as part of the car.

1928 Chevrolet AB National two-door sedan, street-rod conversion, front view
A second look at the Ocala conversion, because one photograph can flatter and two rarely do. The modern bumper, exposed engine ancillaries, mirrors, wheels and interior all repeat the same message from every angle — exactly the test to apply to any car you inspect. A conversion announces itself consistently, in details a seller's description may not mention. Judge consistency, not adjectives: an original National is original in the engine bay, the cabin and the brakes, not just in the silhouette.

Which one to buy

Every National is the same year, engine and gearbox, so your choice is a body, a condition and a level of honesty:

The overriding rule: on a Chevrolet National, buy the wood, the engine's hot oil pressure and the title — in that order — and let the paint be whatever it is. A National with sound framing, a healthy four and clean paperwork can be improved a cheque at a time; a shiny National without them cannot.

Listed now

On Classic Listings today: 1 car is listed here; 0 for sale and 0 marked sold.

See the 1 National cars currently listed.

The market — recorded sales

No dated sales recorded for this series yet — as sales are recorded, they will appear here with their dates and prices.

What they sell for

AB National sale prices

Related guides

Chevrolet 3100 Trucks buyer's guideChevrolet C/K Trucks buyer's guideChevrolet C1 buyer's guideChevrolet C2 buyer's guideChevrolet C3 buyer's guideChevrolet C4 buyer's guideChevrolet AB National buyer's guide